-
APPLICATION TYPE
Main dimensions
-
APPLICATION TYPE
STEEL END BRACKET SETSteel end bracket set completes both chian ends and allow for fastening on outer radius and inner radius: mounting position must be specified. Stainless steel can be delivered on request.
End brackets set for
-
GUIDE SUPPORT
For correct functioning of the chain it is
BRYLON 6 TECHNICAL DATA
Norms Properties Units Dry Conditioned TERMICHE DSC Melting point (10° C/min.) °C ASTM - D 696 Coefficient of linear thermal expansion X10-6 K-1 ASTM D 648
ISO 75
DIN 53461Heat distortion temperature
ISO 75 1.82 N/mm2 °C 210
DIN 53461 0.45 N/mm2
°C
°C
210
220U. L. 94 Flammability H.B. IEC 695-2-1 Incandescent wire
Temperature °C 650
Thickness
650
3FLAMMABILITY ASTM-D 257 Volume resistivity Ohm cm 1015 1011 ASTM-D 257 Surface resistivity Ohm 1013 1011 ASTM-D 149 Dielectric strength KV/mm 22 ASTM-D 150 Dielectric constant (10 Hz) - 3.8 4.5 ASTM-D 150 Dissipation factor (10Hz) - 0.02 0.09 PHYSICAL PROPERTIES ASTM-D 792 Density g/cm3 1.38 ASTM-D 570 Water absorption at 23°C in water for 24 hours % 0.90 MECHANICAL PROPERTIES ASTM-D 638
ISO R/527
DIN 53455Tensile yield stress
Ultimate elongationN/mm2
%195
2.6115
4ASTM-D 638
ISO R/527
DIN 53457Tensile modulus of elasticity N/mm2 10600 6900 ASTM-D 790
ISO 178
DIN 53452Flexural strength N/mm2 310 190 ASTM-D 790
ISO 178Flexural modulus N/mm2 10500 6800 ASTM-D 256 Unnotched Izod impact strength J/m 140 300 ISO 180/4C Notched Izod impact strength KJ/m2 110 125 ASTM-D 785 Rockwell hardness Scala R 122 114 CHEMICAL RESISTANCE
BRYLON 6 BRYLON 6 STEEL Chemical agents Concentration % Amorphous Crystal Methyl acetate 100 RB3 RB2 RB Acetone 100 RB4 RB RB Acetic acid (aqueous solution) 40 AF AF AF Acetic acid (aqueous solution) 10 AF AF AF Acetic acid AF AF AF Citric acid 10 AD 15 RD AD Hydrochloric acid (aqueous solution) 36 S S S Hydrochloric acid (aqueous solution) 10 AF AF S Hydrochloric acid (aqueous solution) 2 AF AD S Chromic acid (aqueous solution) 10 AF AF AF Chromic acid (aqueous solution) 1 RD RD AF Hydrofluoric acid 40 AF AF S Formic acid (aqueous solution) 85 S S AD Formic acid (aqueous solution) 40 S AF AF AD Phosphoric acid (aqueous solution) 10 AF AF S Oleic acid 100 RB3 RB3 RD Sulphuric acid 98 S S S Sulphuric acid (aqueous solution) 40 AF AF S Sulphuric acid (aqueous solution) 10 AF AF S Sulphuric acid (aqueous solution) 2 AF AD S Tartaric acid (aqueous solution) RD RB RD Water RB10 RB9 RD Chlorine water RD RD AD Ethyl alcohol 96 RD17 RB3 RB Ammonia 10 RB11 RB AF Petrol 100 RB1 RB RB Bitumen RD RD RB Potassium carbonate 100 RB RB AF Sodium carbonate 10 RB10 RB3 AF Ammonium chloride (aqueous solution) 10 RB RB AF Calcium chloride (aqueous solution) 20 S S AF Calcium chloride (aqueous solution) 10 RB RB AF Sodium chloride 10 RB RB AF Formaldehyde (aqueous solution) 30 RD RB AD Fat RB RB RB Milk RB RB RB Mercury RB RB RB Oils RB RB RB Oil RB RB RB Paraffin oil RB RB RB Silicon oil RB RB RB Diesel oil RB RB RB Mineral oil RB RB RB Ozone AF AF AF Oil RB RB RB Potassium hydroxide (aqueous solution) 10 RB9 RB3 S Sodium hydroxide (aqueous solution) 50 RD RD S Sodium hydroxide (aqueous solution) 10 RB5 RB S Sodium hydroxide (aqueous solution) 5 RB9 RB S Aluminium sulphate 10 RB RB AF Soap (aqueous solution) RB RB RB Tincture of iodine AF AF AD Trichloroethylene RD5 RD4 RB Vaseline RB RB RB Legend
The table shows the resistance to chemical agents of BRYLON 6 and Steel. The number by resistance value side shows which is the % weight increase due to swelling.
RB - Very good resistance.
RD - Good resistance.
AD - Limited resistance.
AF - Poor resistance.
S - Soluble.
Amorphous - Polymer in amorphous state.
Crystal - Polymer in crystalline state.
